Scepter® Rigid PVC Fittings

rigid pvc


Ask an Expert

Scepter® Rigid PVC conduit fittings off a wide range of boxes, fittings, couplings and elbows.

Scepter offers a comprehensive offering of PVC nonmetallic conduit fittings including adapters, couplings, elbows, access fittings, boxes, cover plates and expansion fittings virtually any fitting required to complete the PVC conduit system.

Easy installations, the ability to perform in demanding environments and labor savings are the reasons nonmetallic conduit fittings chosen by contractors. Scepter PVC conduit fittings offer both high impact and tensile strength, are nonconductive and are resistant to a wide range of chemicals such as acids, alkalis and salt solutions.

rigid pvc fittings group shot

Product Details

Available in 1/2″ – 8″ (12mm – 200mm) sizes

Scepter rigid PVC fittings can be used in nearly any application from Utilities, Airports, Parking garages to water and sewer treatment plants

Suitable for exposed, concrete encased and direct burial, IPEX PVC fittings are concrete tight in all weather conditions and offer high impact and tensile strength

Rigid PVC conduit installation


Advantages of Scepter Conduit

  • Fire resistant: IPEX’s proprietary PVC compound used to manufacture Scepter products is a self-extinguishing material and will not support combustion. Samples taken from an actual fire show the outer surface of the conduit was blistered and charred. The interior of the conduit, however, was unaffected. Additionally, the undamaged conductors were then removed and reinstalled in new conduit. Fire-resistant characteristics when tested to CAN ULC S102.2.
  • Nonconducting: Scepter Rigid PVC Conduit pipe and fittings are nonsparking and nonconducting, thereby eliminating the most dangerous ‘second point of contact’ and ‘phase to ground’ faults. The use of a separate grounding conductor in a Scepter PVC conduit system gives a complete and positive ground for the whole system.
Subway tunnel above the ground


Discover more about IPEX

Our resources section covers everything you need to know: Take a look at our most popular resources below


Product Details

All wiring shall be installed in Rigid PVC conduit and secured to PVC boxes and cabinets by means of proper fittings. All boxes, access fittings and covers shall be furnished with threaded brass inserts, brass screws and PVC gaskets. Rigid PVC fittings and junction boxes shall be used for all outlets, pull boxes and junction points. All PVC junction boxes shall be NEMA 1, 2, 3, 4, 4X, 6P*, 12 and 13 rated and UL Listed for wet locations. *Applies only to 4″ to 12″ non-hinged covers

Exposed conduit shall be securely held in place by suitable hangers or straps with the maximum spacing of points for supports not exceeding those specified in the CEC or NEC. Except when embedded in concrete, rigid conduit pipe shall not be clamped tightly. It shall be supported in such a manner as to permit adequate linear movement, allowing for expansion and contraction of conduit due to temperature change. Where a temperature change exceeding 25°F (14°C) is anticipated, rigid PVC expansion joints shall be installed in accordance with the manufacturer’s recommendations.

Proper care shall be taken when field bending, to maintain the internal diameter and wall thickness of the conduit. The contractor shall furnish and install Scepter Rigid PVC conduit pipe and fittings made by IPEX. Where the engineer’s specifications indicate Scepter products or equivalent, the equivalent shall be CSA certified and accepted by the Canadian Electrical Code. Due to broad manufacturing tolerances, all pipe and fitting products shall be of the same manufacturer.



1/2″ – 8″ (12 – 200 mm)

C22.2 No. 211.2, CSA C22.2 No. 211.0, CSA C22.2 No. 85
NSF Certified to UL651
Sunlight Resistant
Rated for use with 90°C conductors
Corps. of Engineers Spec. CE 303:01
Military Spec, Federal Spec. WC 1094A
Cements and Primers are UL GREENGAURD Gold certified

Parking Garages
Car Washes
Fish Plants
Steel Mills
Bridges and Tunnels
Water Treatment Plants
Sewage Treatment Plants
Pulp and Paper Industries
Street and Highway Lighting
Food Processing Plants

Find what you need?

Whether you are new to thermoplastic solutions or a long-standing customer, your local Customer Service and in-field Technical Sales Representatives provide the support you need. It's this service that distinguishes IPEX in the marketplace.

Back to top